BOSTONSTANGS.COM

jgt8229 · jgt8229

so my cars ben running decent , i need some new suspension every little bump is killing my car lol bolts keep coming loose. im looken for something good for dailydriving and some beter handle would be nice too. i would like to lower it slightly from stock but i live around alot of pot holes and speeds bumps...

jgt8229 · jgt8229

i was wonder whats the average compresionreadings would be on a 91 motor with 90k.

boostd710 · boostd710

I keep blowing headlight bulbs due to my passenger headlight housing leaking water/condensation into it. They are ultra clear headlights from latemodelrestoration.com. I sent them back once and had them replaced for free already and they have done the same thing. What can i do to seal them up? i rtv...

boostd710 · boostd710

my starter just shit the bed. I have no tools at my house to do this and my car is now a paper weight. Can someone help... I live in worcester by the airport. 508 963 9854 - Jay

supertukes · supertukes

anyone ever change an extension housing gasket? pretty sure thats where my leak is coming from.... how hard is it to be done?

DMURB · DMURB

i just picked up a 98 gt with a blown head gasket. i was told that in these motors if the car sits for a while with a blown head gasket i might as well just buy a new motor. is this true. can i just replace the head gasket and be fine or should i do a motor swap. if you think motor swap anyone know where i can find one c...

Timbo8650 · Timbo8650

well my girlfriends 05 trailblazer stalls randomly while either taking a turn while not on the gas or sometimes just going from reverse to drive. the rpm's drop to the point where it shuts off. any ideas??

droptopfox · droptopfox

okay my buddy has a 98 f150 its been a great truck so when the head gasket wennt at 230k we decided to do a 5.4 swap so now its a 5.4 from a 97 expedition he wants more and has a set of patroit stage3 heads sitting around from a lightning would he see more power from using these with a pi intake i dont know anything...

JordanDiD24 · JordanDiD24

Hey so as some of you know i finally have found a car, a 97 gt, and now am trying to figure out what to do to it. Im trying to figure out how to gain both low end and high end power, with not alot of money at the time. I dont plan on doing everything at once, but over the course of a year or so i plan on finishing it. So w...

Green92LX · Green92LX

so the MAF and TPS went bad. car wouldn't idle, when driving it hesitated and sounded like it was missing. the second i pressed the clutch it would shut right down. replaced the MAF, injectors, and TPS. now the car will start up cold, surge for a few seconds, then idle smooth. i can drive it easily for a lit...

droptopfox · droptopfox

anyone ever done them i want to strengthen mine up before i take my car to the track i want to keep this one mint

MRicci · MRicci

Not sure if anyone on here knows, but my dad has been looking at a new motor for his firebird. It is a pontiac 400. If he gets it he can go with either a 650 with vaccuum secondary or a 750 with mechanical. I am not sure on the brands but will find out from him. I know nothing about carbs or sizing so any help would...

jgt8229 · jgt8229

anyone have a how to on how to do drum breaks. i never did them before and need to replace the wheel cylinder and pads. im haven a hard time.

DMURB · DMURB

i have an 89 with a 306 in it. it has a 70 mm bbk tb. this car used to be supercharged but when i bought the car it was no longer in it. they put the stock air box in it with the stock rubber piping. i think the air meter is also back to stock. how do i know if this is stock or if it is still upgraded. if its stock what do i...

supertukes · supertukes

anyone ever do an oil pan on an f150? has a 302 in it, any way to be done w/o pulling the motor?

stang1990 · stang1990

hi guys me and my father in law are trying to fix his stang little by little. my question is everytime we give it gas and rev it to like 4000 rpm and up it hesitates and it wont go even when im driving and i try to go faster it just wont go it hesitates and its embarrasing lol but it just wont go what do you guys thin...

91notch · 91notch

I have new lines for a 93 cobra brake setup. New booster and MC for a two line setup. Has anyone made their stang identical to this setup? I need to by a new porp valve. Any suggestions?

93 LX FiveO · 93 LX FiveO

just cruising around i noticed my car hesitates pretty bad below 2500 rpm's kinda bogs out and works itself up the rpm's once it hits 2500, it takes off... i got no codes or symptons really. fuel filter and plugs are new. has a brand new topend. could it be clutch related?

snakebite · snakebite

i have a clean 1986 2wd ranger 6 foot bed 4cyl 5 speed i also have a rebuilt 93 5.0 bolted to a new t5 and new clutch making motor mounts,exhaust,drive shaft ,fuel lines return lines that's all easy stuff for me my question is has anybody on here ever made a mustang injection harness work in somethin...

Silver GT · Silver GT

2000 GT 4.6 SOHC WINDSOR 96,000 miles. Ive run nothing but mobile 1 since 54K. Ive been hearing a noise for some time now ONLY WHEN THE ENGINE IS COLD. It started off light but is now getting worse (louder)!! Once the car warms up it goes away but i did notice it once at the track after about 8-10 runs when...

remy824 · remy824

i had just bought a 98 gt but the owner had lost the key so i put a new steering column in it and now it wont start and the theft light blinks does anyone know how to fix this without bringing it to the dealer?

wheels · wheels

buying a used nos kit off a friend dirt cheap for my 04 gt it is a wet kit wondering if anyone knows of any writeups and or where i hook up the fuel??

shadybrady · shadybrady

i have a 89 mustang gt with rear disc brakes on it well i too the rear axels out of a 91 mark 7 and i have the brakes that go with that well i dont know what i should use for brake cables any one know how i should do it or where i can have them made up let me know thanxs

fast2000mustanggt · fast2000mustanggt

ive done some research on the swap i know you can use the intake on the 5.4 or can swap and use the addapters for the 4.6 and you need to get an 8 bolt flywheel.... shortied headers from 4.6 bolt right up and that ecm,harness is the same needs bigger fuel pump ive heard but not sure.... anyone know anything i h...

supertukes · supertukes

my buddy bought this car and its got a pretty bad starting problem once its hot, here's his post from another site... "I have a '93 5.0 lx with very low miles. The car starts cold and runs perfect. When I shut it off and try to restart it while its hot it either hesitates and starts or doesnt start at a...

jgt8229 · jgt8229

hi, so since im selling my stang i figure ide pick up a nice daily driver for now . i was seriously considering a mark 8, seems like the next best thing from a mustang and a nice cruising car. i was wondering if there are any really bad problems in theese cars to look out for, and what to look for when buying one...

supertukes · supertukes

aright so i just put a 5" tach in my car, and everything works fine, i hooked up the light inside the tach to the parking lights, the switched power to the tach to a switched from the ign. switch, and obv ground to ground and the other wire to the tach source, well, my problem is that when i hit where i set...

T76 Cobra · T76 Cobra

1990 mustang GT ...buddy has 17x9s all around 4lugs ...thinking about running 275s on the back which shouldnt be a problem but the fronts i think they will rub so maybe 255s ? car is lowered a little not sure if that will come into play ...what tire size are some of you guys running any problems ? thanks

5pointslow · 5pointslow

not sure what to use ... ive got enough stuff to do before i buy a meth kit but im at the point i would need to mock up a intercooler for fitment....wasnt sure about pros and cons of each and the better of the 2? thanks

dave · dave

i have a 90 mustang with 4lug disc brakes need 2 know what cables to get some people say the svo mustang cables will work does anybody know for sure

DMURB · DMURB

i have a tremmec tko tranny. do i need a specific mount for that or does any v-8 tranny mount work. thanks

FoxBodyFan · FoxBodyFan

i have found a 1980 Capri (Mustang) and i have some questions. its all stock 4 cyl. 4 spd. and i want to know if it has a posi rear end and i would also like to know how close the interior is to a Mustang GT?

fast2000mustanggt · fast2000mustanggt

i have a 2000 mustang gt im buying a bottom end from DSS racing i need to know if i have the romeo or windsor block......

boostd710 · boostd710

So I cannot have a passenger in my car without scraping my exhaust on the FLAT GROUND! If I go over the crown of the road, or if I hit a MINOR bump I scrape my H-Pipe. I looked at it, and the owner before me cut the hangers off the H-Pipe. Now I never had an issue with this before and I am running 4 cyl springs in the...

Silver GT · Silver GT

Is there a specific year that i have to order to work with my 2000 GT? Ive been looking around but cant find much, some say 99 04 and some say 01 04! I just want to make sure before i buy one.

5pointslow · 5pointslow

i bought a fuel cell for my car that has a gm sending unit i can buy a 90-10 ohm or a 70-30 ohm i realy wanted to use my factory fuel gauge to keep the orig cluster

remy824 · remy824

i have a chance to get a nice cat back for my 95 cobra but its off a 1993 mustang my question is will it fit??? if not what is different thanks

Timbo8650 · Timbo8650

the dick where i got my sticker failed me because my exhaust is too loud. its only flowmasters with an off road x pipe. besides switching my exhaust, is there any way i can quite it down just for an hour or so to get a sticker? -- Edited by uatlb on Monday 20th of April 2009 03:36:39 PM

boostd710 · boostd710

my car is a 1990. So the other day I noticed that my passenger headlight both high and low beams were out. So I go pick up a set of sylvania bulbs and replace both passenger and driver headlights. Everything was fine that day and night, then the next day I am leaving work and noticed that my passenger bult bl...

NotchFoxStang89 · NotchFoxStang89

hey guys i hope one of you can help me out here... im changing my interior over to black so i took the original dash out changed the heater core while i was at it put the black one in and now the car does not start... everthing works fine, lights, horn, gauges, no wires were unplugged so i have no idea... i turn...

93 LX FiveO · 93 LX FiveO

i keep getting this code and i dont know why i simply upgraded the injectors and got the matching pro-m 75mm maf calibrated for the 24lb injectors. ever since its been hooked up my car runs sluggish at random times... most noticeably after its been wide open a couple times. it gets to the point where...

chris · chris

so i didnt know what section this would fall under so maybe you can help. i have a 98 gsxr 750 its fuel injected i had just replaced the plugs and along with that i had fixed a few vacuum hoses that were cracked torn now the bike doesnt want to idle the bike runs 100x better and also the battery is not charging i...

flamingpony83 · flamingpony83

i bought an autometer air/fuel guage, my question is what wire off o2 harness on passenger side is the "signal wire"??? i hooked it up to grey/blue wire and it shows one green light on guage and it never changes during a drive. help me out please.

Timbo8650 · Timbo8650

it will start idling normal a little below 1000rpm but will randomly jump up as high as 2000 and just stay there until i shut it off and restart it. then it will be good again as long as i drive like an old lady and dont rev up too high, but the second i go more than 1/4 throttle the rpms just hang way too high. the...

MustangMayhem · MustangMayhem

Will a rear end out of a 94 bolt up to an 83. If not what kinda mods do you have to do to make it work if any Or will it not work at all lol

91notchback · 91notchback

can you convert power doors to crank doors? im talking about the actual doors can you take out the power mecanism and convert it to crank? if so can you explain how? im sorry i dont know if you could help me thatll be great

mustang50lx88 · mustang50lx88

http://www.veryuseful.com/mustang/tech/engine/images/88-91_5.0_EEC_Wiring_Diagram.gif

mustang50lx88 · mustang50lx88

http://www.muscularmustangs.com/gears.php

supertukes · supertukes

new pushrods should be arriving tuesday, going to get it back together then, anyone know the steps to adjust the valve lash? let me know

5pointslow · 5pointslow

going on my notch with 408 and t trim gonna be 75% -80% strip car and a little street what do you guys think go low and clean with just enough to clear the 351 intake or go mean and big ?

Topic		Started By	Replies	Views	Last Post
	new susption? (Preview) so my cars ben running decent , i need some new suspension every little bump is killing my car lol bolts keep coming loose. im looken for something good for dailydriving and some beter handle would be nice too. i would like to lower it slightly from stock but i live around alot of pot holes and speeds bumps...	jgt8229	6	925	Oct 4, 2009 by jgt8229
	compression (Preview) i was wonder whats the average compresionreadings would be on a 91 motor with 90k.	jgt8229	3	741	Oct 4, 2009 by jgt8229
	headlight condensation (Preview) I keep blowing headlight bulbs due to my passenger headlight housing leaking water/condensation into it. They are ultra clear headlights from latemodelrestoration.com. I sent them back once and had them replaced for free already and they have done the same thing. What can i do to seal them up? i rtv...	boostd710	12	1285	Oct 2, 2009 by boostd710
	Anyone around right now that can come do a starter in my car? (Preview) my starter just shit the bed. I have no tools at my house to do this and my car is now a paper weight. Can someone help... I live in worcester by the airport. 508 963 9854 - Jay	boostd710	9	723	Oct 2, 2009 by boostd710
	f150 trans leak... (Preview) anyone ever change an extension housing gasket? pretty sure thats where my leak is coming from.... how hard is it to be done?	supertukes	0	616	Oct 1, 2009 by supertukes
	98 gt head gasket. (Preview) i just picked up a 98 gt with a blown head gasket. i was told that in these motors if the car sits for a while with a blown head gasket i might as well just buy a new motor. is this true. can i just replace the head gasket and be fine or should i do a motor swap. if you think motor swap anyone know where i can find one c...	DMURB	9	890	Sep 17, 2009 by DMURB
	05 trail blazer... (Preview) well my girlfriends 05 trailblazer stalls randomly while either taking a turn while not on the gas or sometimes just going from reverse to drive. the rpm's drop to the point where it shuts off. any ideas??	Timbo8650	22	995	Sep 16, 2009 by bonzcnc
	patriot heads on my buddies truck (Preview) okay my buddy has a 98 f150 its been a great truck so when the head gasket wennt at 230k we decided to do a 5.4 swap so now its a 5.4 from a 97 expedition he wants more and has a set of patroit stage3 heads sitting around from a lightning would he see more power from using these with a pi intake i dont know anything...	droptopfox	0	669	Sep 8, 2009 by droptopfox
	Car help/advice? (Preview) Hey so as some of you know i finally have found a car, a 97 gt, and now am trying to figure out what to do to it. Im trying to figure out how to gain both low end and high end power, with not alot of money at the time. I dont plan on doing everything at once, but over the course of a year or so i plan on finishing it. So w...	JordanDiD24	12	742	Sep 7, 2009 by Mineral 02
	car's running like shit, help... (Preview) so the MAF and TPS went bad. car wouldn't idle, when driving it hesitated and sounded like it was missing. the second i pressed the clutch it would shut right down. replaced the MAF, injectors, and TPS. now the car will start up cold, surge for a few seconds, then idle smooth. i can drive it easily for a lit...	Green92LX	5	912	Sep 6, 2009 by mikefheath87
	compatition enginering torque box reneforcement (Preview) anyone ever done them i want to strengthen mine up before i take my car to the track i want to keep this one mint	droptopfox	5	796	Sep 2, 2009 by 93 LX FiveO
	Carb Question? (Preview) Not sure if anyone on here knows, but my dad has been looking at a new motor for his firebird. It is a pontiac 400. If he gets it he can go with either a 650 with vaccuum secondary or a 750 with mechanical. I am not sure on the brands but will find out from him. I know nothing about carbs or sizing so any help would...	MRicci	4	749	Aug 27, 2009 by cobraman24
	drum brakes (Preview) anyone have a how to on how to do drum breaks. i never did them before and need to replace the wheel cylinder and pads. im haven a hard time.	jgt8229	14	811	Aug 26, 2009 by BigHenault
	?'s about my mass air meter (Preview) i have an 89 with a 306 in it. it has a 70 mm bbk tb. this car used to be supercharged but when i bought the car it was no longer in it. they put the stock air box in it with the stock rubber piping. i think the air meter is also back to stock. how do i know if this is stock or if it is still upgraded. if its stock what do i...	DMURB	20	1138	Aug 23, 2009 by DMURB
	1994 f150 oil pan (Preview) anyone ever do an oil pan on an f150? has a 302 in it, any way to be done w/o pulling the motor?	supertukes	9	870	Aug 15, 2009 by qwik88
	re:question about my stang (Preview) hi guys me and my father in law are trying to fix his stang little by little. my question is everytime we give it gas and rev it to like 4000 rpm and up it hesitates and it wont go even when im driving and i try to go faster it just wont go it hesitates and its embarrasing lol but it just wont go what do you guys thin...	stang1990	10	952	Jul 30, 2009 by sean86gt
	Brake porportion valve??? which one? (Preview) I have new lines for a 93 cobra brake setup. New booster and MC for a two line setup. Has anyone made their stang identical to this setup? I need to by a new porp valve. Any suggestions?	91notch	1	688	Jul 27, 2009 by Mustang5L5
	bad hesitation below 2500 (Preview) just cruising around i noticed my car hesitates pretty bad below 2500 rpm's kinda bogs out and works itself up the rpm's once it hits 2500, it takes off... i got no codes or symptons really. fuel filter and plugs are new. has a brand new topend. could it be clutch related?	93 LX FiveO	6	803	Jul 8, 2009 by 93 LX FiveO
	LOOKING FOR SOME 5.0 KNOWLEDGE I KNOW SOMEONE ON HERE CAN HELP ME (Preview) i have a clean 1986 2wd ranger 6 foot bed 4cyl 5 speed i also have a rebuilt 93 5.0 bolted to a new t5 and new clutch making motor mounts,exhaust,drive shaft ,fuel lines return lines that's all easy stuff for me my question is has anybody on here ever made a mustang injection harness work in somethin...	snakebite	9	941	Jul 7, 2009 by jgt8229
	HELP!!! 2V TIMING CHAIN TENSIONERS?????? (Preview) 2000 GT 4.6 SOHC WINDSOR 96,000 miles. Ive run nothing but mobile 1 since 54K. Ive been hearing a noise for some time now ONLY WHEN THE ENGINE IS COLD. It started off light but is now getting worse (louder)!! Once the car warms up it goes away but i did notice it once at the track after about 8-10 runs when...	Silver GT	9	881	Jul 6, 2009 by Silver GT
	1998 mustang wont start theft light blinks (Preview) i had just bought a 98 gt but the owner had lost the key so i put a new steering column in it and now it wont start and the theft light blinks does anyone know how to fix this without bringing it to the dealer?	remy824	6	1812	Jun 30, 2009 by Nunzio
	NOS (Preview) buying a used nos kit off a friend dirt cheap for my 04 gt it is a wet kit wondering if anyone knows of any writeups and or where i hook up the fuel??	wheels	6	1018	Jun 28, 2009 by LX546
	need help (Preview) i have a 89 mustang gt with rear disc brakes on it well i too the rear axels out of a 91 mark 7 and i have the brakes that go with that well i dont know what i should use for brake cables any one know how i should do it or where i can have them made up let me know thanxs	shadybrady	2	711	Jun 20, 2009 by 93 LX FiveO
	swapping out the worn and tired 85.xxx 4.6 for 5.4SOHC (Preview) ive done some research on the swap i know you can use the intake on the 5.4 or can swap and use the addapters for the 4.6 and you need to get an 8 bolt flywheel.... shortied headers from 4.6 bolt right up and that ecm,harness is the same needs bigger fuel pump ive heard but not sure.... anyone know anything i h...	fast2000mustanggt	1	731	Jun 15, 2009 by T76 Cobra
	starting issues (Preview) my buddy bought this car and its got a pretty bad starting problem once its hot, here's his post from another site... "I have a '93 5.0 lx with very low miles. The car starts cold and runs perfect. When I shut it off and try to restart it while its hot it either hesitates and starts or doesnt start at a...	supertukes	12	1130	Jun 12, 2009 by supertukes
	mark 8 (Preview) hi, so since im selling my stang i figure ide pick up a nice daily driver for now . i was seriously considering a mark 8, seems like the next best thing from a mustang and a nice cruising car. i was wondering if there are any really bad problems in theese cars to look out for, and what to look for when buying one...	jgt8229	18	1077	Jun 11, 2009 by jgt8229
	tach wiring? (Preview) aright so i just put a 5" tach in my car, and everything works fine, i hooked up the light inside the tach to the parking lights, the switched power to the tach to a switched from the ign. switch, and obv ground to ground and the other wire to the tach source, well, my problem is that when i hit where i set...	supertukes	10	827	Jun 7, 2009 by mustang50lx88
	Question on tire size on a Foxbody (Preview) 1990 mustang GT ...buddy has 17x9s all around 4lugs ...thinking about running 275s on the back which shouldnt be a problem but the fronts i think they will rub so maybe 255s ? car is lowered a little not sure if that will come into play ...what tire size are some of you guys running any problems ? thanks	T76 Cobra	9	1939	Jun 1, 2009 by snakebite
	meth injecton vs an intercooler ?? any opinions? (Preview) not sure what to use ... ive got enough stuff to do before i buy a meth kit but im at the point i would need to mock up a intercooler for fitment....wasnt sure about pros and cons of each and the better of the 2? thanks	5pointslow	4	749	Jun 1, 2009 by qwik88
	emergency brake help (Preview) i have a 90 mustang with 4lug disc brakes need 2 know what cables to get some people say the svo mustang cables will work does anybody know for sure	dave	1	696	May 28, 2009 by Mustang5L5
	question about my transmission (Preview) i have a tremmec tko tranny. do i need a specific mount for that or does any v-8 tranny mount work. thanks	DMURB	3	778	May 28, 2009 by cmont
	help a brotha out (Preview) i have found a 1980 Capri (Mustang) and i have some questions. its all stock 4 cyl. 4 spd. and i want to know if it has a posi rear end and i would also like to know how close the interior is to a Mustang GT?	FoxBodyFan	6	779	May 26, 2009 by FoxBodyFan
	romeo or windsor block... (Preview) i have a 2000 mustang gt im buying a bottom end from DSS racing i need to know if i have the romeo or windsor block......	fast2000mustanggt	2	701	May 20, 2009 by Mineral 02
	H-Pipe hanging too low all of a sudden... (Preview) So I cannot have a passenger in my car without scraping my exhaust on the FLAT GROUND! If I go over the crown of the road, or if I hit a MINOR bump I scrape my H-Pipe. I looked at it, and the owner before me cut the hangers off the H-Pipe. Now I never had an issue with this before and I am running 4 cyl springs in the...	boostd710	14	1024	May 17, 2009 by supertukes
	SVT FOCUS FUEL PUMP (Preview) Is there a specific year that i have to order to work with my 2000 GT? Ive been looking around but cant find much, some say 99 04 and some say 01 04! I just want to make sure before i buy one.	Silver GT	4	822	May 16, 2009 by Silver GT
	sending unit question (Preview) i bought a fuel cell for my car that has a gm sending unit i can buy a 90-10 ohm or a 70-30 ohm i realy wanted to use my factory fuel gauge to keep the orig cluster	5pointslow	1	686	May 10, 2009 by LX546
	1993 cat back on my 95 cobra???? (Preview) i have a chance to get a nice cat back for my 95 cobra but its off a 1993 mustang my question is will it fit??? if not what is different thanks	remy824	2	723	Apr 30, 2009 by T76 Cobra
	big red "R" for my exhaust.... (Preview) the dick where i got my sticker failed me because my exhaust is too loud. its only flowmasters with an off road x pipe. besides switching my exhaust, is there any way i can quite it down just for an hour or so to get a sticker? -- Edited by uatlb on Monday 20th of April 2009 03:36:39 PM	Timbo8650	15	1154	Apr 29, 2009 by Cervinis92GT
	Passenger Headlight bulb keeps blowing out... (Preview) my car is a 1990. So the other day I noticed that my passenger headlight both high and low beams were out. So I go pick up a set of sylvania bulbs and replace both passenger and driver headlights. Everything was fine that day and night, then the next day I am leaving work and noticed that my passenger bult bl...	boostd710	1	659	Apr 29, 2009 by sled
	Starting Problems!! (Preview) hey guys i hope one of you can help me out here... im changing my interior over to black so i took the original dash out changed the heater core while i was at it put the black one in and now the car does not start... everthing works fine, lights, horn, gauges, no wires were unplugged so i have no idea... i turn...	NotchFoxStang89	8	734	Apr 27, 2009 by NotchFoxStang89
	code 66 maf low signal (Preview) i keep getting this code and i dont know why i simply upgraded the injectors and got the matching pro-m 75mm maf calibrated for the 24lb injectors. ever since its been hooked up my car runs sluggish at random times... most noticeably after its been wide open a couple times. it gets to the point where...	93 LX FiveO	3	662	Apr 26, 2009 by 93 LX FiveO
	idling to low (Preview) so i didnt know what section this would fall under so maybe you can help. i have a 98 gsxr 750 its fuel injected i had just replaced the plugs and along with that i had fixed a few vacuum hoses that were cracked torn now the bike doesnt want to idle the bike runs 100x better and also the battery is not charging i...	chris	2	677	Apr 26, 2009 by chris
	Air/fuel guage.... (Preview) i bought an autometer air/fuel guage, my question is what wire off o2 harness on passenger side is the "signal wire"??? i hooked it up to grey/blue wire and it shows one green light on guage and it never changes during a drive. help me out please.	flamingpony83	1	702	Apr 24, 2009 by LX546
	86 idling way up (Preview) it will start idling normal a little below 1000rpm but will randomly jump up as high as 2000 and just stay there until i shut it off and restart it. then it will be good again as long as i drive like an old lady and dont rev up too high, but the second i go more than 1/4 throttle the rpms just hang way too high. the...	Timbo8650	7	770	Apr 20, 2009 by mikefheath87
	1994 rear end into a fox body (Preview) Will a rear end out of a 94 bolt up to an 83. If not what kinda mods do you have to do to make it work if any Or will it not work at all lol	MustangMayhem	8	774	Apr 19, 2009 by MustangMayhem
	can you convert power doors to crank doors? (Preview) can you convert power doors to crank doors? im talking about the actual doors can you take out the power mecanism and convert it to crank? if so can you explain how? im sorry i dont know if you could help me thatll be great	91notchback	8	766	Apr 17, 2009 by 91notchback
	88-91 5.0 EEC Wiring Diagram (Preview) http://www.veryuseful.com/mustang/tech/engine/images/88-91_5.0_EEC_Wiring_Diagram.gif	mustang50lx88	0	998	Apr 15, 2009 by mustang50lx88
	"Choosing the Right Speedometer Gears" (Preview) http://www.muscularmustangs.com/gears.php	mustang50lx88	0	621	Apr 15, 2009 by mustang50lx88
	adjusting valve lash (Preview) new pushrods should be arriving tuesday, going to get it back together then, anyone know the steps to adjust the valve lash? let me know	supertukes	4	764	Apr 13, 2009 by GTStang
	2inch steel cowl hood or go big like 4 1/2,5, 6 incher (Preview) going on my notch with 408 and t trim gonna be 75% -80% strip car and a little street what do you guys think go low and clean with just enough to clear the 351 intake or go mean and big ?	5pointslow	15	977	Apr 12, 2009 by 5pointslow
«First < 1 2 3 4 5 … 8 > Last» \| Page of 8 sorted by